Sand pot metal?
-
- Victor III
- Posts: 516
- Joined: Sat Oct 14, 2017 5:40 pm
- Personal Text: Greg
- Location: Central Maryland
Sand pot metal?
I was wondering, has anyone tried sanding pot metal parts? I have a radio switch valve from my 7-25X that’s so stuck up it could hardly move. This is due to the pot metal expanding. Is this something that can be sanded, or are there any other methods of getting this valve unstuck?
-
- Victor IV
- Posts: 1065
- Joined: Mon Jun 28, 2010 12:12 pm
- Location: Cranberry Township, PA
Re: Sand pot metal?
If possible expose the part to cold air, perhaps in a refrigerator. Others may have ideas too.
-
- Victor VI
- Posts: 3751
- Joined: Mon Oct 03, 2011 7:54 pm
Re: Sand pot metal?
I have successfully used emery paper to make Columbia and Pathé pot metal tonearm joints usable. It was a case of do a little, then test, repeat as needed.
- Curt A
- Victor Monarch Special
- Posts: 6437
- Joined: Fri Jul 09, 2010 8:32 pm
- Personal Text: Needle Tins are Addictive
- Location: Belmont, North Carolina
Re: Sand pot metal?
Sanding pot metal definitely works... use fine sandpaper or emory cloth.
"The phonograph is not of any commercial value."
Thomas Alva Edison - Comment to his assistant, Samuel Insull.
"No one needs a Victrola XX, a Perfected Graphophone Type G, or whatever you call those noisy things."
My Wife
Thomas Alva Edison - Comment to his assistant, Samuel Insull.
"No one needs a Victrola XX, a Perfected Graphophone Type G, or whatever you call those noisy things."
My Wife
-
- Victor III
- Posts: 816
- Joined: Thu Sep 25, 2014 4:25 pm
- Location: North Central Iowa
Re: Sand pot metal?
Do you have a picture of your valve? I have one around here somewhere that I can hunt up that's working and I don't have any use for it, but It's out of a 7-3 and I'm not sure if they are the same.
-
- Victor III
- Posts: 516
- Joined: Sat Oct 14, 2017 5:40 pm
- Personal Text: Greg
- Location: Central Maryland
Re: Sand pot metal?
This is the valve, it’s from a VV 7-25. As I recall this valve is a bit taller than the 7-3 but I could be wrong. I’m just going to use this with a small portable speaker so it isn’t really crucial. My radio is MIA.
-
- Victor III
- Posts: 816
- Joined: Thu Sep 25, 2014 4:25 pm
- Location: North Central Iowa
Re: Sand pot metal?
I will do some digging around and see where I put that thing I have, it sure looks a lot like it's the way I remember it. A Radiola 18 wouldn't be hard to hunt up for that machine. Victor must have used a horn driver on that machine, like the 7-3 and then the machine is just acoustic. The machine you have is nice looking, but they don't turn up very often. I've only seen one over the years. Up north of Minneapolis the 7-3's and 7-30's must have sold in large numbers as I've seen a couple dozen of those things up there and bought a few as well. That's where this valve would have come from. I bought an Alhambra up there a couple of years ago that had batteries in it for the Radiola 20 that had 1951 expiration dates on them! They must not have gotten AC power up there until after the war. I don't know why a Radiola 60 wouldn't fit into your cabinet either, it seems like the chassis is about the same size. Those horn drivers sound surprisingly good that Victor used, but they had the same diaphragm as the orthophonic reproducer in them.
-
- Victor II
- Posts: 391
- Joined: Sat Jan 17, 2009 4:17 pm
Re: Sand pot metal?
Somebody else years ago had the same idea---change out the radio for the Radiola 60. Some years ago I got my 7-25X off of eBay and it has the 60 installed as a later upgrade. I think the Radiola 60 was thought of as a better performer. No idea why they felt the need to paint the case glossy black and the metal Radiola bezels (and the grille cloth!) metallic gold. This poor thing is waiting for me to retire and tackle the restoration work.
- Attachments
-
- VE7-25Asis02.jpg (96.4 KiB) Viewed 1825 times
-
- Victor III
- Posts: 516
- Joined: Sat Oct 14, 2017 5:40 pm
- Personal Text: Greg
- Location: Central Maryland
Re: Sand pot metal?
Ouch! That poor machine! I hope you fix it up, it's a beautiful machine in nice condition. This model really showcases the blended finishes that Victor used.
-
- Victor II
- Posts: 391
- Joined: Sat Jan 17, 2009 4:17 pm
Re: Sand pot metal?
Thanks for the good clear photo, Greg. Now I know what to aim for when I get busy on mine, and it's bound to be interesting to see how near the Victor finish I can get. Guess I'll have to stick a crowbar in my wallet to pry out a few bills and buy some good airbrush equipment so I can do those shading effects. On mine the top 2 layers of veneer have long ago parted ways with the lid, so I'll have to redo that. Naturally, by the time I'm done I'll have more invested in this than it's ever going to be worth. Just can't bring myself to part it out and junk the case.
- Attachments
-
- VE7-25Asis01.jpg (90.18 KiB) Viewed 1745 times