I didn't see the motor in the picture, but I could be wrong. I was most likely mistaken about the unique motor, the OP would just have to find a 4 spring with the winding key in the proper place. I was under the impression that many models contained unique motors, however that is not the case. Taking a look at the Victor Motor Guide, there were only about 16 total types. WhoopsJerryVan wrote:Was the motor not there? What's so unique about the motor in this model?GregVTLA wrote:Good luck on this one! There's unfortunately not much left, but It's still savable. You'll most likely need to make a new motor board and fit a different motor, since the machine is so scarce. Can't wait to see it done though!
I ended up feeling sorry for that VV-360 in Michigan.
-
- Victor III
- Posts: 516
- Joined: Sat Oct 14, 2017 5:40 pm
- Personal Text: Greg
- Location: Central Maryland
Re: I ended up feeling sorry for that VV-360 in Michigan.
-
- Victor III
- Posts: 816
- Joined: Thu Sep 25, 2014 4:25 pm
- Location: North Central Iowa
Re: I ended up feeling sorry for that VV-360 in Michigan.
The whole machine is there. I took it apart somewhat to get the thing out and into my truck. The motor is just the usual 4 spring motor that Victor used through the 20's. And I finished taking it all apart before I brought it down to the basement. The doors didn't want to open and shut properly and one of the hinges was broken, so I figured I'd better just get it apart so I could clamp the doors down to get the flattened out, and start getting all the veneer off the thing so I can figure out what I need to do from there.
The worst part about these modern veneers is that they are so thin, and they used relatively thick veneers back in the 20's yet. Some of the two-ply veneers aren't as thick as the poplar crossbanding that's on this machine. I've gotten into that before, so I'll have to glue face veneer to the two-ply veneer and then the three layers is about the same as two was when this thing was made.
Below is a picture from his craigslist ad.
The worst part about these modern veneers is that they are so thin, and they used relatively thick veneers back in the 20's yet. Some of the two-ply veneers aren't as thick as the poplar crossbanding that's on this machine. I've gotten into that before, so I'll have to glue face veneer to the two-ply veneer and then the three layers is about the same as two was when this thing was made.
Below is a picture from his craigslist ad.
- pughphonos
- Victor III
- Posts: 756
- Joined: Tue Jul 17, 2012 12:35 pm
- Personal Text: Ms. Pugh
- Location: Homewood, Illinois, USA
Re: I ended up feeling sorry for that VV-360 in Michigan.
Earl, just wanted to congratulate you on this project--but above all for the HEART you show in everything you do--every commitment you make. I will never forget all the helpful advice you gave me when I bought my Lyon & Healy reproducing studio grand piano a couple years ago. She still has her challenges, but with the help of Jerry Biasella (sp?) I'm making progress.
Ralph
Ralph
"You must serve music, because music is so enormous and can envelop you into such a state of perpetual anxiety and torture--but it is our first and main duty"
-- Maria Callas, 1968 interview.
-- Maria Callas, 1968 interview.
-
- Victor III
- Posts: 516
- Joined: Sat Oct 14, 2017 5:40 pm
- Personal Text: Greg
- Location: Central Maryland
Re: I ended up feeling sorry for that VV-360 in Michigan.
Wow, that picture makes it look a hundred times better than the first image! I'd thought you had a gutted ruined cabinet, but it's a lot closer than I thought. Good luck and I hope to see it when it's done!