I have a spring from an amberola that broke near the middle. I cut the middle out and I want to cut another hole. I tried with a drill, but I can't get it to go through, and it's difficult to get a good angle. Would it be easier to do with a dremel or should go to a metal worker? Are there any tips on how to cut a hole in the spring? Keep in mind it's the one on the inside. Thanks in advanced
-Martin
How should I cut another hole in m winding spring?
- Mormon S
- Victor III
- Posts: 737
- Joined: Mon May 07, 2018 6:27 pm
- Personal Text: Martin "phono_fluff" on instagram
-
- Victor IV
- Posts: 1204
- Joined: Mon Apr 26, 2010 3:13 pm
Re: How should I cut another hole in m winding spring?
In order to drill a hole in a piece of spring steel, it needs to be heated with a torch to remove the temper. But-- If you are trying to repair a spring by riveting pieces together, I strongly advise against it. The potential for long-term success is low, while the potential to do damage to the spring barrel, gears or to yourself is high. A new spring from Ron Sitko is not very expensive. If you'd rather not install it yourself, you can send him the barrel and he will install the new spring for you.
Brad Abell
Brad Abell
- Curt A
- Victor Monarch Special
- Posts: 6440
- Joined: Fri Jul 09, 2010 8:32 pm
- Personal Text: Needle Tins are Addictive
- Location: Belmont, North Carolina
Re: How should I cut another hole in m winding spring?
Brad is right... splicing a spring is not a good idea. The spring is tempered steel and may shatter if spliced. If you were trying to make a new hole to repair an inch or two close to the end, that might work... To drill a hole in a spring, you have to heat it red hot and let it gradually cool to remove the temper. To re-temper it, you have to heat it red hot and immediately plunge it into a container of oil or water to cool it...
"The phonograph is not of any commercial value."
Thomas Alva Edison - Comment to his assistant, Samuel Insull.
"No one needs a Victrola XX, a Perfected Graphophone Type G, or whatever you call those noisy things."
My Wife
Thomas Alva Edison - Comment to his assistant, Samuel Insull.
"No one needs a Victrola XX, a Perfected Graphophone Type G, or whatever you call those noisy things."
My Wife
- startgroove
- Victor III
- Posts: 887
- Joined: Sat Apr 20, 2013 3:01 pm
- Location: Coos Bay, Oregon
Re: How should I cut another hole in m winding spring?
Brad and Curt offer good advice. It is possible to successfully re-hole the end of a spring. I've fixed many springs by heating them to a red glow and then natural cooling de-anneals them enough to punch a hole. Shown here is a punch tool that makes it easy to do that. It is available a Harbor Freight and also Ebay (around $20).
- edisonphonoworks
- Victor IV
- Posts: 1566
- Joined: Wed Oct 21, 2009 10:50 am
- Personal Text: A new blank with authentic formula and spiral core!
- Contact:
Re: How should I cut another hole in m winding spring?
I also purchase new springs, and don't repair old ones. I did repair them when I was starting out, but then found Ron Sitko, APSCO, Wyatt's Musical Americana,The Smiths, so never repaired a spring again. I usually replace all of the set.
- Mormon S
- Victor III
- Posts: 737
- Joined: Mon May 07, 2018 6:27 pm
- Personal Text: Martin "phono_fluff" on instagram
Re: How should I cut another hole in m winding spring?
Thank you guys for the responses. I'll get a new spring. How much would does Ron charge for a spring? I can't find much information, but I'll call next weekend if I can.edisonphonoworks wrote:I also purchase new springs, and don't repair old ones. I did repair them when I was starting out, but then found Ron Sitko, APSCO, Wyatt's Musical Americana,The Smiths, so never repaired a spring again. I usually replace all of the set.
-
- Victor III
- Posts: 516
- Joined: Sat Oct 14, 2017 5:40 pm
- Personal Text: Greg
- Location: Central Maryland
Re: How should I cut another hole in m winding spring?
I recently purchased one, and he charged $27.50 for a VTM spring. I imagine all of the others would be similar in price.
-
- Victor II
- Posts: 297
- Joined: Tue Nov 13, 2012 5:57 pm
Re: How should I cut another hole in m winding spring?
I thoroughly recommend Ron Sitko as I have purchased parts from him on several occasions including one time when I needed a main - spring of unusual dimensions . At the time Ron had a length of stock spring of correct size and he kindly made one up for me to required length and spec , including the necessary end fittings. Dulcetto
-
- Victor O
- Posts: 88
- Joined: Tue Feb 07, 2017 8:17 pm
- Personal Text: phonographs are like potato chips you can't just have one
- Location: Long island ny
Re: How should I cut another hole in m winding spring?
I just drilled a hole no problem take a center punch put the spring on a piece of wood and slame it. Drill bit went through no problem. It was a spring for a Pathé actuelle . I used 2 bits to make the pair shape and filed the center. I got the idea from the complete talking machine book by Mr Eric Reiss