Does anyone know if changing the mandrel gear will cut down on motor noise on the Amberola 30 and 50.
Mark is offering new original stock mandrel gears. I did buy two of them.
https://rover.ebay.com/rover/0/0/0?mpre ... 2344800691
Amberola Motor Noise
-
- Victor V
- Posts: 2694
- Joined: Fri Nov 18, 2011 11:23 pm
- Location: NW Indiana VV-IV;
-
- Victor Jr
- Posts: 1
- Joined: Thu Jul 05, 2018 11:55 am
Re: Amberola Motor Noise
Hi...i am a new user here. I have had issues with motor noise with the Strathclyde 305m but a thorough cleaning of the motor pulley enabled the belt to sit properly and the noise is gone. There's the tiniest bit of motor noise when I'm standing no more than a foot away and the amp's off. I also recently acquired a Sansui 222 and it makes a grinding sound as it starts up. While running it is a little noisier in operation than the Strathclyde but not by much.
pcb assembly supplier
pcb assembly supplier
Last edited by MattyLada on Thu Aug 09, 2018 11:01 am, edited 1 time in total.
-
- Victor IV
- Posts: 1269
- Joined: Sun Oct 25, 2009 12:53 pm
- Location: Michiana
Re: Amberola Motor Noise
MattyLada wrote:Hi...i am a new user here. I have had issues with motor noise with the Strathclyde 305m but a thorough cleaning of the motor pulley enabled the belt to sit properly and the noise is gone. There's the tiniest bit of motor noise when I'm standing no more than a foot away and the amp's off. I also recently acquired a Sansui 222 and it makes a grinding sound as it starts up. While running it is a little noisier in operation than the Strathclyde but not by much.
I'm afraid that you may be posting at cross purposes, O. M.
The Strathclyde is a bit modern for us, as this forum is primarily for the study of pre-1930 mechanical talking machines such as the Amberola 50 pictured below.
https://youtu.be/UYkT5sIriss
You are referring to a turntable which post dates the subject machines of this forum by sixty or seventy years.
Oh, and yes, most noise problems in a post-fire Amberola motor may be cYes by replacing the governor drive gear - IF - The mandrel springs are intact.
- MicaMonster
- Victor III
- Posts: 845
- Joined: Sat Feb 28, 2009 12:52 pm
- Personal Text: Never Settled
- Location: Rochester, NY
- Contact:
Re: Amberola Motor Noise
SOMETIMES that gear will in fact reduce the noise. The issue is that at some time in the past, people removed the mandrel from these while there was still spring tension, and the drive gear would grind a few edges of the mandrel gear teeth flat...making them noisey.
-Antique Phonograph Reproducer Restorer-
http://www.EdisonDiamondDisc.com
Taming Orthophonics Daily!
http://www.EdisonDiamondDisc.com
Taming Orthophonics Daily!
-
- Victor IV
- Posts: 1269
- Joined: Sun Oct 25, 2009 12:53 pm
- Location: Michiana
Re: Amberola Motor Noise
As a rule you are absolutely correct. A standardized Amberola mechanism which is in good nick is pretty darned quiet. When one of these machines is noisy our old friend No 4020, the mandrel drive gear, is usually to be blamed. Over the years I have seen a few of these whigh were actually worn out, with more than half of the meat on the governor drive teeth worn away. Damage from incompetent repair is, as you note, quite common. More common than heavy wear, actually.MicaMonster wrote:SOMETIMES that gear will in fact reduce the noise. The issue is that at some time in the past, people removed the mandrel from these while there was still spring tension, and the drive gear would grind a few edges of the mandrel gear teeth flat...making them noisey.