Need a photo of lid support on VV 4-7
- chrisg
- Victor III
- Posts: 546
- Joined: Sat Oct 05, 2013 10:24 am
- Location: North Carolina
- Contact:
Need a photo of lid support on VV 4-7
Trying to help a gentleman out. He contacted me needing the lid support hinge. I think i got a junk one twenty years ago and parted it. I have the support i think was on it. But he said his as two hole on the lid and two screw holes on the motor board. Any photo would be great.
-
- Victor V
- Posts: 2180
- Joined: Sat Jul 09, 2016 7:12 pm
Re: Need a photo of lid support on VV 4-7
I saw this online --
FROM -- https://www.ebay.com/itm/VICTOR-Victrol ... 7675.l2557
Hope this helps.
OrthoFan
FROM -- https://www.ebay.com/itm/VICTOR-Victrol ... 7675.l2557
Hope this helps.
OrthoFan
- chrisg
- Victor III
- Posts: 546
- Joined: Sat Oct 05, 2013 10:24 am
- Location: North Carolina
- Contact:
Re: Need a photo of lid support on VV 4-7
Maybe they had several type. The supports i saved look like the photo below. But what you show sounds like what he described. Thanks
- mattrx
- Victor IV
- Posts: 1140
- Joined: Wed Oct 12, 2011 9:55 am
- Location: Bartlett, TN
Re: Need a photo of lid support on VV 4-7
I once had a 4-7 that had this same lid support. I no longer have it, unfortunately, or I'd post photos. It did not have the 2 spring loaded arms shown in another post. There could well have been variations, I suppose. There often were.OrthoFan wrote:I saw this online --
FROM -- https://www.ebay.com/itm/VICTOR-Victrol ... 7675.l2557
Hope this helps.
OrthoFan
Matt
- AZ*
- Victor IV
- Posts: 1143
- Joined: Thu Jan 15, 2009 8:51 pm
- Location: USA
Re: Need a photo of lid support on VV 4-7
My 4-7 is similar to the image that chrisg posted.
Best regards ... AZ*
- chrisg
- Victor III
- Posts: 546
- Joined: Sat Oct 05, 2013 10:24 am
- Location: North Carolina
- Contact:
Re: Need a photo of lid support on VV 4-7
Thank you to all. I guess I will see when he brings it in
-
- Victor V
- Posts: 2180
- Joined: Sat Jul 09, 2016 7:12 pm
Re: Need a photo of lid support on VV 4-7
According to "The Victor Data Book" by Robert Baumbach, the spring balanced lid supports were introduced with the model VV 4-7 (type A) starting with serial number 38001.
OrthoFan
OrthoFan
-
- Victor II
- Posts: 239
- Joined: Wed Nov 12, 2014 5:50 pm
Re: Need a photo of lid support on VV 4-7
Mine is SN 11046 and has the support with two screws at each end. Nice machine. My first orthophonic. Neil
- electrolaman 64
- Victor II
- Posts: 229
- Joined: Fri May 18, 2018 7:49 pm
- Personal Text: Look for the Dog
- Location: Indianapolis, IN
- Contact:
Re: Need a photo of lid support on VV 4-7
The 4-7 had spring loaded pots like a credenza. I junked a 4-7 earlier this year and have the lid supports if someone needs them. In fact I ahve all of the hardware form this model and the grille.
Carlton Smith
Indianapolis, IN
Carlton Smith
Indianapolis, IN
Carlton Smith
Indianapolis, IN
electrolaman 64
Indianapolis, IN
electrolaman 64