Edison Fireside B: Speed Control
- RolandVV-360
- Victor II
- Posts: 301
- Joined: Fri Nov 04, 2016 3:57 pm
- Personal Text: The Finest Gift of All!
- Location: Central Virginia
- Contact:
Edison Fireside B: Speed Control
When I release the brake on my Fireside, I find that the mandrel spins faster than the proper speed for a BA. Below are some pictures of the governor and speed control assembly. If anyone could show me to whatever is wrong, I would greatly appreciate it.
PHONOGRAPH, n. An irritating toy that restores life to dead noises. -Ambrose Bierce
-Roland
-Roland
-
- Victor VI
- Posts: 3751
- Joined: Mon Oct 03, 2011 7:54 pm
Re: Edison Fireside B: Speed Control
I don't see anything out of the ordinary offhand. If the speed control doesn't adjust the speed enough, you will probably need to adjust the position of the governor.
- RolandVV-360
- Victor II
- Posts: 301
- Joined: Fri Nov 04, 2016 3:57 pm
- Personal Text: The Finest Gift of All!
- Location: Central Virginia
- Contact:
Re: Edison Fireside B: Speed Control
Is that true to all Fireside machines? It seems like a a nuisance to have to adjust the brake to perfection every time I want to play a cylinder...52089 wrote:I don't see anything out of the ordinary offhand. If the speed control doesn't adjust the speed enough, you will probably need to adjust the position of the governor.
PHONOGRAPH, n. An irritating toy that restores life to dead noises. -Ambrose Bierce
-Roland
-Roland
-
- Victor IV
- Posts: 1229
- Joined: Wed Aug 01, 2012 8:43 pm
- Location: Port Huron, MI
Re: Edison Fireside B: Speed Control
Is the yoke with the felt pads there? I don't see it in the picture. Without that, you won't be able to control the speed.
Dave D
Dave D
- phonogfp
- Victor Monarch Special
- Posts: 7402
- Joined: Wed Jan 07, 2009 5:08 pm
- Personal Text: "If you look for the bad in people expecting to find it, you surely will." - A. Lincoln
- Location: New York's Finger Lakes
Re: Edison Fireside B: Speed Control
Gosh no - - nobody said anything about adjusting the brake! Dave meant adjusting the governor laterally in its bearings. However, in your picture, the governor looks to be positioned correctly. Here are two possible fixes:RolandVV-360 wrote:Is that true to all Fireside machines? It seems like a a nuisance to have to adjust the brake to perfection every time I want to play a cylinder...52089 wrote:I don't see anything out of the ordinary offhand. If the speed control doesn't adjust the speed enough, you will probably need to adjust the position of the governor.
1) Loosen the set screw that holds the governor collar in place. Move the collar/weights/limit disc laterally on the governor shaft toward the right - - just a fraction of an inch so it's a bit closer to the pads on the yoke.
2) Here's the simplest. The yoke is indeed in place, but it may have been slightly bent if the governor shaft was ever removed by an inexperienced person. The yoke is made of brass and easily bent, which means it can be carefully returned to its original position with the pads a bit closer to the limit disc. Easy does it!
Good luck - -
George P.
-
- Victor Monarch Special
- Posts: 8516
- Joined: Tue Feb 10, 2009 11:25 am
- Personal Text: Stop for a visit when in Oregon.
- Location: Albany, Oregon
Re: Edison Fireside B: Speed Control
Roland,
I'm sure you, as an experienced collector/repairman, will run the spring before adjusting the governor but to all newer collectors... Before working on the governor or any spring motor in general always run the motor down as far as possible. With a cylinder machine slipping off the belt from the upper pulley will help it run down more completely. Good luck with your project. Jerry Blais
I'm sure you, as an experienced collector/repairman, will run the spring before adjusting the governor but to all newer collectors... Before working on the governor or any spring motor in general always run the motor down as far as possible. With a cylinder machine slipping off the belt from the upper pulley will help it run down more completely. Good luck with your project. Jerry Blais