Hi,
I'm attempting to disassemble a no. 2 reproducer in order to replace the gaskets. I removed all the screws, dug out the old flange, and removed the stylus bar. For some reason, I am unable to remove the back cover. I tried prying it open with a screwdriver. Suggestions are appreciated.
Thanks,
Kevin
Unable to open No. 2 Reproducer
- novkev24
- Victor I
- Posts: 177
- Joined: Mon Aug 30, 2010 8:42 pm
- Location: Doylestown, PA
- Contact:
Unable to open No. 2 Reproducer
The purchase of a Genuine Victrola closes the Avenue of Future Regret.
- ANNOUNCEMENT The Victrola Shortage Today (New Castle News, Friday, December, 20, 1918)
- ANNOUNCEMENT The Victrola Shortage Today (New Castle News, Friday, December, 20, 1918)
- Zeppy
- Victor III
- Posts: 699
- Joined: Wed Jan 07, 2009 2:51 pm
- Location: Gaithersburg, MD
Re: Unable to open No. 2 Reproducer
Take the needle bar off, cut the diaphragm out, and either try to tap it apart, or get a small screw driver and try to wedge it between the two parts from the inside. I'm guessing the red rubber gasket has degraded in such a way that it may be acting as a glue...just a wild guess.
- novkev24
- Victor I
- Posts: 177
- Joined: Mon Aug 30, 2010 8:42 pm
- Location: Doylestown, PA
- Contact:
Re: Unable to open No. 2 Reproducer
Thanks for the reply. I was hoping to save the diaphragm, but what you are saying makes sense.
The purchase of a Genuine Victrola closes the Avenue of Future Regret.
- ANNOUNCEMENT The Victrola Shortage Today (New Castle News, Friday, December, 20, 1918)
- ANNOUNCEMENT The Victrola Shortage Today (New Castle News, Friday, December, 20, 1918)
-
- Victor VI
- Posts: 3463
- Joined: Wed Jan 07, 2009 3:21 pm
Re: Unable to open No. 2 Reproducer
Im not sure if heating it might break the stronghold??
And dont worry...mica wont burn
And dont worry...mica wont burn
- novkev24
- Victor I
- Posts: 177
- Joined: Mon Aug 30, 2010 8:42 pm
- Location: Doylestown, PA
- Contact:
Re: Unable to open No. 2 Reproducer
Won't the paper label next to the diaphragm burn?
The purchase of a Genuine Victrola closes the Avenue of Future Regret.
- ANNOUNCEMENT The Victrola Shortage Today (New Castle News, Friday, December, 20, 1918)
- ANNOUNCEMENT The Victrola Shortage Today (New Castle News, Friday, December, 20, 1918)
-
- Victor VI
- Posts: 3463
- Joined: Wed Jan 07, 2009 3:21 pm
Re: Unable to open No. 2 Reproducer
Ummm....Good point
- novkev24
- Victor I
- Posts: 177
- Joined: Mon Aug 30, 2010 8:42 pm
- Location: Doylestown, PA
- Contact:
Re: Unable to open No. 2 Reproducer
I ended up punching a hole in the reproducer and heating the gasket with a flame. The rubber became soft enough to pull out. Thanks everyone for your advice.
Regards,
Kevin
Regards,
Kevin
The purchase of a Genuine Victrola closes the Avenue of Future Regret.
- ANNOUNCEMENT The Victrola Shortage Today (New Castle News, Friday, December, 20, 1918)
- ANNOUNCEMENT The Victrola Shortage Today (New Castle News, Friday, December, 20, 1918)