FOR SALE: Edison Disc Reproducer Holders: $75 + Shipping
Posted: Fri Jul 21, 2017 11:46 am
Thanks to a talented friend, a cooperative foundry, and a master machinist, I can now offer excellent reproductions of the rare Edison single reproducer holder that clamps to the motor plate:
There has been some discussion on this forum as to the origin of these cast holders (I know of one original and a reported second). Some believe they were supplied by a manufacturer of lateral adapters. Others believe that they were supplied by Edison for Dance Reproducers or Edisonic Reproducers. Still others believe these cast holders came with kits to convert conventional Edison Disc Phonographs to Long Play capability. (One known kit - never used - indeed has a single reproducer holder, but it is the stamped metal variety that screws into the cabinet.)
I happen to believe that this cast holder that clamps to the motor plate was a short-lived Edison product, and here's why:
Note the shaped channel in the reproduction holder (above) which accepts the Edison motor plate is identical to that on the Edison "Long/Short" switch assembly (bottom). Both original components are cast iron (the reproduction is cast bronze). I can't prove it, but my gut tells me this clamp-on reproducer holder was an Edison product. Typical Edison over-engineering. In any event, it's quite rare, and very handy.
Unlike the stamped steel double holders found in the Edison Long Play consoles, and the one known single stamped holder found with an L-P kit, these cast holders DO NOT SCREW INTO THE CABINET. These holders can be transferred from machine to machine if desired, without marring cabinetry.
They can of course be used for storing & displaying lateral adapters, Dance Reproducers, Edisonic Reproducers, or an additional conventional Edison Reproducer.
These reproductions are identical to the original except for being cast bronze rather than cast iron. (A magnet is the only way to tell the difference.) After casting, these were machined in a custom-made jig, deburred, finished, and painted (one coat primer plus two coats black). The result is a beautiful reproduction.
There were only 13 of these that passed the critical standards of my friend. One has already been sold, which leaves a dozen as shown in the photo below:
The price on these is $75 each + $7.15 Priority Mail shipping in the continental U.S. If more than one is desired, I will refund any savings in postage. No Paypal, but your check or money order is fine. If interested, PM me and I will reserve a holder for you while your payment makes its way to me.
I'll be happy to answer any questions, post additional photos, etc.
Thanks, and best to all,
George P.
There has been some discussion on this forum as to the origin of these cast holders (I know of one original and a reported second). Some believe they were supplied by a manufacturer of lateral adapters. Others believe that they were supplied by Edison for Dance Reproducers or Edisonic Reproducers. Still others believe these cast holders came with kits to convert conventional Edison Disc Phonographs to Long Play capability. (One known kit - never used - indeed has a single reproducer holder, but it is the stamped metal variety that screws into the cabinet.)
I happen to believe that this cast holder that clamps to the motor plate was a short-lived Edison product, and here's why:
Note the shaped channel in the reproduction holder (above) which accepts the Edison motor plate is identical to that on the Edison "Long/Short" switch assembly (bottom). Both original components are cast iron (the reproduction is cast bronze). I can't prove it, but my gut tells me this clamp-on reproducer holder was an Edison product. Typical Edison over-engineering. In any event, it's quite rare, and very handy.
Unlike the stamped steel double holders found in the Edison Long Play consoles, and the one known single stamped holder found with an L-P kit, these cast holders DO NOT SCREW INTO THE CABINET. These holders can be transferred from machine to machine if desired, without marring cabinetry.
They can of course be used for storing & displaying lateral adapters, Dance Reproducers, Edisonic Reproducers, or an additional conventional Edison Reproducer.
These reproductions are identical to the original except for being cast bronze rather than cast iron. (A magnet is the only way to tell the difference.) After casting, these were machined in a custom-made jig, deburred, finished, and painted (one coat primer plus two coats black). The result is a beautiful reproduction.
There were only 13 of these that passed the critical standards of my friend. One has already been sold, which leaves a dozen as shown in the photo below:
The price on these is $75 each + $7.15 Priority Mail shipping in the continental U.S. If more than one is desired, I will refund any savings in postage. No Paypal, but your check or money order is fine. If interested, PM me and I will reserve a holder for you while your payment makes its way to me.
I'll be happy to answer any questions, post additional photos, etc.
Thanks, and best to all,
George P.