The Talking Machine Forum — For All Antique Phonographs & Recordings
http://forum.talkingmachine.info/

WANTED: Cylinder reamer
http://forum.talkingmachine.info/viewtopic.php?f=9&t=35083
Page 1 of 2

Author:  OldRestorer [ Fri Apr 13, 2018 4:35 pm ]
Post subject:  WANTED: Cylinder reamer

I am going to try repairing a bunch of my cylinders. I would like a reamer. Used is fine, crappy is fine. It just needs to ReAm!

Thanks!
Kirk

Author:  Stephen_Madara [ Fri Apr 13, 2018 7:24 pm ]
Post subject:  Re: Want to buy: Cylinder reamer and Mandrel

I have an unused old oak reamer that needs sandpaper strips attached and an amberola mandrel I could let you have the pair for 40.00 plus actual shipping if you are interested.

Attachments:
IMG_20180413_191241058.jpg
IMG_20180413_191241058.jpg [ 1.66 MiB | Viewed 911 times ]

Author:  OldRestorer [ Sun Apr 15, 2018 6:30 pm ]
Post subject:  Re: Want to buy: Cylinder reamer and Mandrel

I am going to need a shaft on the mandrel. Are there threads in the end that I can use a rod in? I see some online with shafts.
Thanks
Kirk

Author:  Lucius1958 [ Sun Apr 29, 2018 10:11 am ]
Post subject:  Re: Want to buy: Cylinder reamer and Mandrel

OldRestorer wrote:
I am going to need a shaft on the mandrel. Are there threads in the end that I can use a rod in? I see some online with shafts.
Thanks
Kirk


If it's from a 30/50/75, at least, it would have been held on the shaft by a collar with a set screw.

Bill

Author:  Herman [ Sun Apr 29, 2018 1:50 pm ]
Post subject:  Re: Want to buy: Cylinder reamer and Mandrel

OldRestorer wrote:
I am going to need a shaft on the mandrel. Are there threads in the end that I can use a rod in? I see some online with shafts.
Thanks
Kirk

Have you found what you needed? I have a mandrel from a 2min only Home. Perfect for what you want as it has a very beefy shaft. No reamer though.

Herman

Author:  OldRestorer [ Sun Apr 29, 2018 2:51 pm ]
Post subject:  Re: Want to buy: Cylinder reamer and Mandrel W shaft

Hello,
I was offered the above but I need a shaft on it.
It should look like this photo below.
I need a good shaft for stability when trying to reform these cylinders. If it even works..

Kirk

Attachments:
Screen Shot 2018-04-29 at 2.47.14 PM.png
Screen Shot 2018-04-29 at 2.47.14 PM.png [ 143.81 KiB | Viewed 737 times ]

Author:  Herman [ Sun Apr 29, 2018 4:03 pm ]
Post subject:  Re: Want to buy: Cylinder reamer and Mandrel W shaft

The most rigid shaft you will find attached to a mandrel is from the 2min Home as I mentioned in my post. Here is a picture sample I borrowed from a previous post from Victroladoctor. Hope he does not mind. The one I have is in my attic and too hot and lazy right now to bring it down to take pictures. The feedscrew threads on my mandrel are no good so no use on a phonograph but will suit your needs.

$25.00 includes shipping if you are interested.

Attachments:
mandrel (1).JPG
mandrel (1).JPG [ 110.66 KiB | Viewed 733 times ]

Author:  OldRestorer [ Mon Apr 30, 2018 6:50 am ]
Post subject:  Re: Want to buy: Cylinder reamer and Mandrel W shaft

Looks good!
I will take it and will message you.
Kirk

Author:  OldRestorer [ Mon May 14, 2018 9:12 am ]
Post subject:  Re: Want to buy: Cylinder reamer and Mandrel W shaft

Mandrel found!

Stephen_Madara,
Can you sell me just the reamer?
Thanks,
Kirk

Author:  OldRestorer [ Wed Jun 06, 2018 9:31 am ]
Post subject:  Re: WANTED: Cylinder reamer

I have not heard back so I am STILL looking for a reamer.

Thanks,
Kirk

Page 1 of 2 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/