I am going to try repairing a bunch of my cylinders. I would like a reamer. Used is fine, crappy is fine. It just needs to ReAm!
Thanks!
Kirk
WANTED: Cylinder reamer
- OldRestorer
- Victor III
- Posts: 535
- Joined: Sun Mar 19, 2017 7:14 pm
- Location: Long Island NY
WANTED: Cylinder reamer
Last edited by OldRestorer on Sat May 26, 2018 7:08 am, edited 2 times in total.
It's not what you say... It's what you do...
-
- Victor III
- Posts: 550
- Joined: Tue Jan 25, 2011 6:56 pm
- Personal Text: www.glassphonohorns.com
- Contact:
Re: Want to buy: Cylinder reamer and Mandrel
I have an unused old oak reamer that needs sandpaper strips attached and an amberola mandrel I could let you have the pair for 40.00 plus actual shipping if you are interested.
- OldRestorer
- Victor III
- Posts: 535
- Joined: Sun Mar 19, 2017 7:14 pm
- Location: Long Island NY
Re: Want to buy: Cylinder reamer and Mandrel
I am going to need a shaft on the mandrel. Are there threads in the end that I can use a rod in? I see some online with shafts.
Thanks
Kirk
Thanks
Kirk
It's not what you say... It's what you do...
- Lucius1958
- Victor VI
- Posts: 3937
- Joined: Tue Dec 14, 2010 12:17 am
- Location: Where there's "hamburger ALL OVER the highway"...
Re: Want to buy: Cylinder reamer and Mandrel
If it's from a 30/50/75, at least, it would have been held on the shaft by a collar with a set screw.OldRestorer wrote:I am going to need a shaft on the mandrel. Are there threads in the end that I can use a rod in? I see some online with shafts.
Thanks
Kirk
Bill
-
- Victor II
- Posts: 243
- Joined: Sun Jul 30, 2017 5:28 pm
- Location: Deltona FL / Brampton ON
Re: Want to buy: Cylinder reamer and Mandrel
Have you found what you needed? I have a mandrel from a 2min only Home. Perfect for what you want as it has a very beefy shaft. No reamer though.OldRestorer wrote:I am going to need a shaft on the mandrel. Are there threads in the end that I can use a rod in? I see some online with shafts.
Thanks
Kirk
Herman
- OldRestorer
- Victor III
- Posts: 535
- Joined: Sun Mar 19, 2017 7:14 pm
- Location: Long Island NY
Re: Want to buy: Cylinder reamer and Mandrel W shaft
Hello,
I was offered the above but I need a shaft on it.
It should look like this photo below.
I need a good shaft for stability when trying to reform these cylinders. If it even works..
Kirk
I was offered the above but I need a shaft on it.
It should look like this photo below.
I need a good shaft for stability when trying to reform these cylinders. If it even works..
Kirk
- Attachments
-
- Screen Shot 2018-04-29 at 2.47.14 PM.png (143.81 KiB) Viewed 2823 times
It's not what you say... It's what you do...
-
- Victor II
- Posts: 243
- Joined: Sun Jul 30, 2017 5:28 pm
- Location: Deltona FL / Brampton ON
Re: Want to buy: Cylinder reamer and Mandrel W shaft
The most rigid shaft you will find attached to a mandrel is from the 2min Home as I mentioned in my post. Here is a picture sample I borrowed from a previous post from Victroladoctor. Hope he does not mind. The one I have is in my attic and too hot and lazy right now to bring it down to take pictures. The feedscrew threads on my mandrel are no good so no use on a phonograph but will suit your needs.
$25.00 includes shipping if you are interested.
$25.00 includes shipping if you are interested.
- Attachments
-
- mandrel (1).JPG (110.66 KiB) Viewed 2819 times
- OldRestorer
- Victor III
- Posts: 535
- Joined: Sun Mar 19, 2017 7:14 pm
- Location: Long Island NY
Re: Want to buy: Cylinder reamer and Mandrel W shaft
Looks good!
I will take it and will message you.
Kirk
I will take it and will message you.
Kirk
It's not what you say... It's what you do...
- OldRestorer
- Victor III
- Posts: 535
- Joined: Sun Mar 19, 2017 7:14 pm
- Location: Long Island NY
Re: Want to buy: Cylinder reamer and Mandrel W shaft
Mandrel found!
Stephen_Madara,
Can you sell me just the reamer?
Thanks,
Kirk
Stephen_Madara,
Can you sell me just the reamer?
Thanks,
Kirk
It's not what you say... It's what you do...
- OldRestorer
- Victor III
- Posts: 535
- Joined: Sun Mar 19, 2017 7:14 pm
- Location: Long Island NY
Re: WANTED: Cylinder reamer
I have not heard back so I am STILL looking for a reamer.
Thanks,
Kirk
Thanks,
Kirk
It's not what you say... It's what you do...