This topic is deceptively simple, and as you can see, mounting a double formed metal holder can become a relatively complex endeavor.
This is the post I am picking up from:
Brandon, I have two double holders (the formed metal, cabinet mount type) one on a C 250, and one on a C 19. Though your question was in regard to a SINGLE holder, I think the topic of both the single AND double holders ought to be broached. I assume that some of my considerations would be the same for your single holder, so here goes:HisMastersVoice wrote:Mine is the screw-in typedrh wrote:Is yours the bolt-on type, or the kind held to the wood with screws? I bought one of the reproduction bolt-on types that were briefly available through the Yankee Trader section recently. It fits easily between the bedplate and false work, and I slipped it as far to the left as possible to avoid interference with the horn and reproducer in play.HisMastersVoice wrote:This helps me too, I'm going to be adding one to my C-19 soon. Does anyone have the measurements for the placement of the single reproducer holder?
I had planned on eventually storing a variety of devices, for use with both specific machines.
Before mounting the holder, I checked for lid and horn clearances, and mounted the holder for what I thought would be the best compromise for holding a "Regular" (standard), and "Edisonic" reproducer, and eventually, some type of “78” adapter, or maybe even a Long Playing Reproducer.
The locations of the two screw placements I used are:
2-⅜" UP from the turntable trim piece, and 1-¾" and 5-¾" from the left inside of the cabinet wall. (See photo) You should be able to mount your single formed metal holder by using either the far-left screw placement I used; or by using the far-right screw placement I used. OR, you should be able to split the difference, and probably be able to drop your holder DOWN some.
NOTES FOR MOUNTING A DOUBLE HOLDER: After mounting my double holders, and later acquiring large soundbox OroTone and Jewel adapters, I discovered that there were some important considerations for storing them with other various devices I would keep in the holder (keep in mind that anything I did, would likely be a compromise in one fashion or another):
1.) When storing a Long Playing Reproducer in the right-hand socket, the tail WILL contact the horn at its far-left travel, so this reproducer would need to be stored in the left hand socket of the holder. When storing it in the left-hand socket, there are no special considerations.
2.) When storing the Jewel or OroTone adapter using the right-hand socket with the adapter's soundbox in its horizontal position, the edge of the soundbox WILL contact the horn at its far-left travel position. Storing the adapter with the soundbox in its horizontal position, with either a Long Playing OR "Edisonic" reproducer in the left-hand socket, causes contact between the horn, the adapter soundbox, and the reproducer!
3.) When storing the Jewel or OroTone adapter using the left-hand socket, with the adapter's soundbox in the horizontal position, the edge of the soundbox WILL contact the "Automatic Lid Support" (as it was named in the original patent - U.S. 1,303,441; C. E. Wilton), IF the adapter is swiveled to the left.
4.) When storing the "Regular" (standard) and "Edisonic" reproducers, there are no special considerations.
5.) The adapter should always be stored in its vertical position (in either socket), and the LP Reproducer should only be stored in the left socket.
NOTE: When the adapter is in the left socket, with the soundbox in the vertical position, it can be swiveled to its extreme left and not interfere with the lid support. Also, when the adapter is in the right socket, with the sound box in its vertical position, it can be swiveled to its extreme left and not interfere with a reproducer in the left socket.
Given my desire to use this holder for as many different devices as I could, I don't believe that repositioning it on the cabinet would likely result in any real improvement. If I had moved the holder location on the cabinet further to the left, I was concerned that the adapter soundbox, while stored in its preferred vertical position, might contact the lid when closed. That being said, I might have been able to drop the holder down a little more, and not cause any unforeseen issues.
Here are a few photos to show the clearance issues associated with each of the various different applications I needed:
Maybe I went a little overboard with this post, but I'm eager to see how others may have addressed the topic with their own ideas! My positioning of the double holders on my Chippendales probably shouldn't be the last word on the topic, but instead a guide for others to use.
Best,
Fran