Is there a way to remove this motorboard, or at least the motor? Which screws have to be undone?
Help! Removing Oil Bath Motor from 193
-
- Victor IV
- Posts: 1523
- Joined: Wed Jan 07, 2009 10:07 pm
- Location: Lille, France
-
- Victor III
- Posts: 653
- Joined: Thu Aug 13, 2009 5:51 am
Re: Help! Removing Oil Bath Motor from 193
Looks like you have undone the relevant 4 screws, so the motorboard with motor should lift out. Maybe the almost 100 year rubber isolation has stuck the board to the machine. When storing the motor, do store it horizontal, otherwise you may be cleaning oil from the floor
BTW (needle in a haystack) if anyone has one of the leg brace for the short side of a 193, 1 of mine is strangely missing. I thought I'd ask before making a new one. Thanks
BTW (needle in a haystack) if anyone has one of the leg brace for the short side of a 193, 1 of mine is strangely missing. I thought I'd ask before making a new one. Thanks
-
- Victor I
- Posts: 163
- Joined: Thu Aug 15, 2019 1:26 pm
- Personal Text: Spin'em Fast!
- Location: Western North Carolina
Re: Help! Removing Oil Bath Motor from 193
Garret,
Here are two images that should help. The motor hangs from the top plate which rests on the motorboard. I remove my motor by removing the top plate's three retaining screws as well as the speed control plate and mechanism.
The motor is heavy and I slightly raise each side and then slip large zip-ties under the plate and up through the vacant retaining screw holes. I then thread the zip-tie through it's latch, leaving three large loops that can be easily held and which easily lift the motor/plate assembly out of the motor board.
I've replaced springs and serviced the oil pump in mine, so if you would like other images, send me a PM and I will forward them to you.
Robert
Here are two images that should help. The motor hangs from the top plate which rests on the motorboard. I remove my motor by removing the top plate's three retaining screws as well as the speed control plate and mechanism.
The motor is heavy and I slightly raise each side and then slip large zip-ties under the plate and up through the vacant retaining screw holes. I then thread the zip-tie through it's latch, leaving three large loops that can be easily held and which easily lift the motor/plate assembly out of the motor board.
I've replaced springs and serviced the oil pump in mine, so if you would like other images, send me a PM and I will forward them to you.
Robert
-
- Victor IV
- Posts: 1523
- Joined: Wed Jan 07, 2009 10:07 pm
- Location: Lille, France
Re: Help! Removing Oil Bath Motor from 193
Robert,
Thank you so much for these clear images.
The machine isn't mine, but belongs to a collector in Singapore that is having a terrible time with it.
Garret
Thank you so much for these clear images.
The machine isn't mine, but belongs to a collector in Singapore that is having a terrible time with it.
Garret
- Inigo
- Victor VI
- Posts: 3777
- Joined: Mon Dec 18, 2017 1:51 am
- Personal Text: Keep'em well oiled
- Location: Madrid, Spain
- Contact:
Re: Help! Removing Oil Bath Motor from 193
That leg stretcher isn't complex, in case you have to make one... Oops, I'm thinking of a194, maybe the 193 has more complex shape? Although in the web images it seems not too complex. A charpenter might do one for you for not much money...
Inigo
- Dischoard
- Victor II
- Posts: 497
- Joined: Tue Feb 16, 2021 11:41 pm
- Personal Text: Born in the wrong century...
- Location: St. Albans, Vermont
Re: Help! Removing Oil Bath Motor from 193
Sometimes when folks go to remove the motor board they forget one little part and that is to remove the crank. Can't tell you how many times I've neglected to notice it still attached to the side of the machine. Just sayin'
-
- Victor III
- Posts: 653
- Joined: Thu Aug 13, 2009 5:51 am
Re: Help! Removing Oil Bath Motor from 193
Many thanks. I also think its easy, question was just on the off chance - original always better
- Steve
- Victor VI
- Posts: 3179
- Joined: Sun Feb 15, 2009 4:40 pm
- Location: London, Paris, Amsterdam, Berlin, New York, Evesham
Re: Help! Removing Oil Bath Motor from 193
When replacing the top of the motor (lid) be sure to take care to not damage the tiny upright oil lubricating tube which also has to be lined up with the corresponding hole in the top. It's not particularly easy and took me a while to figure it out. You have to almost have the top in place before you can judge the distance by eye, by which time its difficult to see anything as it gets dark quickly!
-
- Victor I
- Posts: 163
- Joined: Thu Aug 15, 2019 1:26 pm
- Personal Text: Spin'em Fast!
- Location: Western North Carolina
Re: Help! Removing Oil Bath Motor from 193
Steve makes a good point! Here is what he is talking about: