Cliff Bolling told me his method of a perfect turntable spindle hole. It is sooooo simple!
Take a governor weight from a later model Victrola, place it curved side down on the felt covered spindle hole, and give a good wack with a hammer. This is the first time I've tried it and it worked perfectly. Try it!
Have others known about this technique? If not, it's officially the "Bolling Spindle Hole Technique."
Jerry Blais
The Cliff Bolling Spindle Hole Technique - It Works!
-
- Victor Monarch Special
- Posts: 8516
- Joined: Tue Feb 10, 2009 11:25 am
- Personal Text: Stop for a visit when in Oregon.
- Location: Albany, Oregon
-
- Victor I
- Posts: 114
- Joined: Fri Jul 18, 2014 10:48 pm
- Location: Orlando, Florida
Re: The Cliff Bolling Spindle Hole Technique - It Works!
We have used this method for years. We buy or cut green felt in squares and use spay glue, making sure to stretch all wrinkles out before the glue dries (about 10 seconds). Then cut around the turntable with a NEW razor blade that has to be super sharp to not pull the fabric. Then use the, "hammering the weight method" of cutting the hole. Works perfect every time!
-
- Victor Monarch Special
- Posts: 5345
- Joined: Mon Aug 24, 2009 3:08 pm
- Location: Southeast MI
Re: The Cliff Bolling Spindle Hole Technique - It Works!
I use a ball bearing.
P.S. Use a smaller hammer when you're working on a cast iron turntable.
P.S. Use a smaller hammer when you're working on a cast iron turntable.
- AZ*
- Victor IV
- Posts: 1143
- Joined: Thu Jan 15, 2009 8:51 pm
- Location: USA
Re: The Cliff Bolling Spindle Hole Technique - It Works!
Gosh, Jerry. Where have you been? I thought EVERYBODY knew this.
(Just kidding, this was news to me too.)
I will definitely try it next time.
(Just kidding, this was news to me too.)
I will definitely try it next time.
Best regards ... AZ*
-
- Victor Monarch Special
- Posts: 5345
- Joined: Mon Aug 24, 2009 3:08 pm
- Location: Southeast MI
Re: The Cliff Bolling Spindle Hole Technique - It Works!
AZ* wrote:Gosh, Jerry. Where have you been? I thought EVERYBODY knew this.
(Just kidding, this was news to me too.)
I will definitely try it next time.
I live in a van, down by the river...
-
- Victor Monarch Special
- Posts: 5345
- Joined: Mon Aug 24, 2009 3:08 pm
- Location: Southeast MI
Re: The Cliff Bolling Spindle Hole Technique - It Works!
https://www.youtube.com/watch?v=hm30l8sqlQwAZ* wrote:Gosh, Jerry. Where have you been? I thought EVERYBODY knew this.
(Just kidding, this was news to me too.)
I will definitely try it next time.
-
- Victor IV
- Posts: 1229
- Joined: Wed Aug 01, 2012 8:43 pm
- Location: Port Huron, MI
Re: The Cliff Bolling Spindle Hole Technique - It Works!
The originals are smooth and don't show the marks in the middle. What is the secret to that?
Dave D
Dave D
-
- Victor Monarch Special
- Posts: 5345
- Joined: Mon Aug 24, 2009 3:08 pm
- Location: Southeast MI
Re: The Cliff Bolling Spindle Hole Technique - It Works!
Dave D wrote:The originals are smooth and don't show the marks in the middle. What is the secret to that?
Dave D
Hi Dave,
Stretching the felt just a bit in all directions before placing the turntable on it, and not putting glue in the center area usually helps. The first step is more difficult if you buy the pre-cut felt. Using a sheet of felt, I place it on a flat surface, pull the edges taut, and lower the turntable onto it, (with glue already applied to the turntable). Then just place some weights on the turntable and let it all dry.
For a pre-cut piece, I've placed the felt on the glued-up turntable, then stretched the material slightly by working it with my hands, rubbing the felt to slide it towards the turntable rim in all directions. Until the glue sets, it will "work", or slide some. I don't use contact cement however, as you'll most likely get no working time with it. I use "Eileen's Tacky Glue". Excellent for felt as it won't soak through. It dries fast, but not so fast that you can't make adjustments. Then place the turntable, face down, on flat surface, weight it, let it dry.
And the ball bearing of course