Hello,
My VE 8-36 has noisy lid springs. Has anyone successfully quietened them down? Oiling or spraying with silicone spray are both options, but before covering the lid springs with something that may just become a dust magnet, I thought it timely to ask what others might have done about this.
Thanks for your input
Don
Noisy Victor 8-35 lid springs
-
- Victor O
- Posts: 57
- Joined: Wed Nov 15, 2017 12:32 am
-
- Victor II
- Posts: 327
- Joined: Tue Jun 02, 2009 10:19 pm
- Location: Silver Spring, MD
Re: Noisy Victor 8-35 lid springs
Here is the Victor Service Bulletin about you 8-35’s balance springs. See section 3 about applying grease to the friction discs. This should take care of the noise.
Mark
Mark
-
- Victor O
- Posts: 57
- Joined: Wed Nov 15, 2017 12:32 am
Re: Noisy Victor 8-35 lid springs
Thank you so much! I'll take a look at this tomorrow - and looking forward to it!
Don
Don
- Dischoard
- Victor II
- Posts: 498
- Joined: Tue Feb 16, 2021 11:41 pm
- Personal Text: Born in the wrong century...
- Location: St. Albans, Vermont
Re: Noisy Victor 8-35 lid springs
I didn't know the 8-35 used that type of closer. I imagine at this point it sounds like when you pull out a folding bed from a sleeper sofa? It makes me appreciate the mech on the 8-30!
-
- Victor O
- Posts: 57
- Joined: Wed Nov 15, 2017 12:32 am
Re: Noisy Victor 8-35 lid springs
Thanks, Mark. That cleared up the issue of noisy springs quite nicely. The pages you posted looked very interesting and I would love to see the others. I don't suppose this is online anywhere, or perhaps you could tell me the title on the first page of the document and I can look into that myself.MarkELynch wrote: ↑Thu Apr 29, 2021 9:53 pm Here is the Victor Service Bulletin about you 8-35’s balance springs. See section 3 about applying grease to the friction discs. This should take care of the noise.
Mark
Again, thank you!
Don
-
- Victor II
- Posts: 327
- Joined: Tue Jun 02, 2009 10:19 pm
- Location: Silver Spring, MD
Re: Noisy Victor 8-35 lid springs
Don,
I’m glad that service bulletin helped. Victor released these single bulletins in loose leaf form and instructed the dealer to place them in a Lefax binder. The Lefax binders contain multiple split rings, hence the series of holes you see in the photos. As new bulletins appeared or updated versions the dealer could add these or update the ones in his binder. Notice the date in the top right corner on the first page and the printing date on the last page.
A number of these bulletins are reproduced in Bob Baumbach’s “Look for the Dog” book. Everyone should own a copy, do you have one? They have not been published in any other form as far as I know.
Mark
I’m glad that service bulletin helped. Victor released these single bulletins in loose leaf form and instructed the dealer to place them in a Lefax binder. The Lefax binders contain multiple split rings, hence the series of holes you see in the photos. As new bulletins appeared or updated versions the dealer could add these or update the ones in his binder. Notice the date in the top right corner on the first page and the printing date on the last page.
A number of these bulletins are reproduced in Bob Baumbach’s “Look for the Dog” book. Everyone should own a copy, do you have one? They have not been published in any other form as far as I know.
Mark
-
- Victor O
- Posts: 57
- Joined: Wed Nov 15, 2017 12:32 am
Re: Noisy Victor 8-35 lid springs
Yes, I had noticed the date, and thank you for explaining the series of bulletins. I would so love to have a set! Yes, I do have "Look for the Dog" and referred to articles periodically (sorry for the pun) as I worked my way through the motor and currently the reproducer. When you need something a little out of the ordinary, I really understand what island living in a foreign (Canada) country is like. A simple thing like Permatex Indian Head Shellac Gasket Compound is virtually nonexistent here on the west coast. Cheap and easy to come by south of the border, but a pain in the rump to get a bottle in one's hand up here. I want to touch up the spider/diaphragm contact points with something that is reversible and consistent with what was done originally. Sigh. A weekend project can take months to complete. A second example: I wish to use softer O-rings before assembling the end caps over the needle arm fulcrums. Not available up here, so I had some sent to a friend in WA who will drop them in the mail for me. The challenges are not always related to engineering. Sigh.MarkELynch wrote: ↑Fri Apr 30, 2021 5:10 pm Don,
I’m glad that service bulletin helped. Victor released these single bulletins in loose leaf form and instructed the dealer to place them in a Lefax binder. The Lefax binders contain multiple split rings, hence the series of holes you see in the photos. As new bulletins appeared or updated versions the dealer could add these or update the ones in his binder. Notice the date in the top right corner on the first page and the printing date on the last page.
A number of these bulletins are reproduced in Bob Baumbach’s “Look for the Dog” book. Everyone should own a copy, do you have one? They have not been published in any other form as far as I know.
Mark