I have two small aluminum horns showing lots of age which I feel are both original. The one which is the typical Columbia horn with the Pat.Appl for on the seam near the nipple has a 7 ⅛ inch bell and is 13 ½ inches in length. The other horn slightly larger has no markings, a 7 ½ inch bell and is 14 inches in length. The other difference is the construction of the smaller end as can be seen in the pictures provided.
Was there another company that produced these small aluminum horn or is this a reproduction?
See pic's provided below.
Any input would be appreciated.
Blizz
Aluminum horn question?? see pic's
- fmblizz
- Victor IV
- Posts: 1180
- Joined: Tue Jan 12, 2010 4:59 pm
- Location: South Jersey
-
- Victor Monarch Special
- Posts: 5346
- Joined: Mon Aug 24, 2009 3:08 pm
- Location: Southeast MI
Re: Aluminum horn question?? see pic's
They both appear original to me.
- phonogfp
- Victor Monarch Special
- Posts: 7404
- Joined: Wed Jan 07, 2009 5:08 pm
- Personal Text: "If you look for the bad in people expecting to find it, you surely will." - A. Lincoln
- Location: New York's Finger Lakes
Re: Aluminum horn question?? see pic's
I agree; both original. I think the horn on the right (with the straight orifice) was an early (ca. 1900-1902) Hawthorne & Sheble product.
The crimped/formed orifice was patented by Charles J. Eichorn (No.797,724), and assigned to the Tea Tray Company. (Hawthorne & Sheble could have manufactured a similar horn under license, of course.) The crimped/formed end seemed to appear around 1902/03, although the patent application wasn't filed until June 14, 1904. (At the time, the U.S. Patent Office allowed filing a patent on a product that had been manufactured for less than two years.)
George P.
The crimped/formed orifice was patented by Charles J. Eichorn (No.797,724), and assigned to the Tea Tray Company. (Hawthorne & Sheble could have manufactured a similar horn under license, of course.) The crimped/formed end seemed to appear around 1902/03, although the patent application wasn't filed until June 14, 1904. (At the time, the U.S. Patent Office allowed filing a patent on a product that had been manufactured for less than two years.)
George P.
- ChuckA
- Victor III
- Posts: 547
- Joined: Thu Jan 15, 2009 6:32 pm
- Personal Text: Learn from the mistakes of others - You can't live long enough to make them all yourself.
- Location: South Eastern PA
- Contact:
Re: Aluminum horn question?? see pic's
If you have a Columbia AW machine you need the horn on the right. The rolled end won't fit the horn mount.
Chuck
Chuck
- fmblizz
- Victor IV
- Posts: 1180
- Joined: Tue Jan 12, 2010 4:59 pm
- Location: South Jersey
Re: Aluminum horn question?? see pic's
enclosed is a picture of an AW reproducer... that would certainly make sense as it looks like the small end actually fits inside the reproducer horn mount thus the rolled/crimped end would prohibit that ..
are there any other cylinder machines that use that type of reproducer ??
Blizz
are there any other cylinder machines that use that type of reproducer ??
Blizz
- Attachments
-
- aw horn.jpg (49.89 KiB) Viewed 991 times
- fmblizz
- Victor IV
- Posts: 1180
- Joined: Tue Jan 12, 2010 4:59 pm
- Location: South Jersey
Re: Aluminum horn question?? see pic's
another pic of the AW reproducer with proper horn??
blizz
blizz