Greetings. The crank for my Victor VI has a crack emanating from one of the slots; I'm not sure how long it's been there, though I suspect it was already present when I found the machine years ago. I discovered it recently when I inspected it after the crank slipped out of the machine a couple of times when I was winding it. I don't know if the crack had anything to do with it, but I have been more mindful while cranking it since and it hasn't happened again. However, I am concerned that the crack could grow and eventually render the crank unusable. Is there anything I can do to reinforce that area to prevent the crack from spreading further?
Thanks!
Victor VI crank
-
- Victor I
- Posts: 139
- Joined: Mon Apr 22, 2019 7:50 pm
-
- Victor VI
- Posts: 3179
- Joined: Fri Oct 06, 2017 11:39 am
- Personal Text: I've got both kinds of music--classical & rag-time.
- Location: South Carolina
Re: Victor VI crank
Hello,
I have a Victor III crank like that and replaced with a new one from JAS Antiques on eBay. I suggest you do the same & have a plater do it in gold to match your machine. It is better to change out parts when they break than to risk damage--on mine it slipped off when my back was turned, unwinding the machine vigorously and throwing the crank out of the case--it took the escutcheon with it & I never found it so now I have a new one on there.
I have a Victor III crank like that and replaced with a new one from JAS Antiques on eBay. I suggest you do the same & have a plater do it in gold to match your machine. It is better to change out parts when they break than to risk damage--on mine it slipped off when my back was turned, unwinding the machine vigorously and throwing the crank out of the case--it took the escutcheon with it & I never found it so now I have a new one on there.
- Dave
- Victor II
- Posts: 327
- Joined: Mon Sep 23, 2013 3:50 pm
- Personal Text: Gramophonist
- Location: KY.
Re: Victor VI crank
I had the same problem with my VI slotted crank. I filled the crack in with some JB Weld Steelstick which will reinforce the metal and prevent further separation.
-
- Victor I
- Posts: 139
- Joined: Mon Apr 22, 2019 7:50 pm
Re: Victor VI crank
Thanks, Dave! Would you mind posting some pictures of the slot area now that might show how you did it and what it looks like now?
- Dave
- Victor II
- Posts: 327
- Joined: Mon Sep 23, 2013 3:50 pm
- Personal Text: Gramophonist
- Location: KY.
Re: Victor VI crank
Sure... here's a pic after i made the repair. The tear was not a great as what you have, but almost. You can barely see it now.
-
- Victor I
- Posts: 139
- Joined: Mon Apr 22, 2019 7:50 pm
Re: Victor VI crank
Looks great! Are you confident it's stable?
A friend recommended brazing. Has anyone tried that?
A friend recommended brazing. Has anyone tried that?
-
- Victor IV
- Posts: 1383
- Joined: Sat Oct 24, 2015 10:46 pm
- Location: riverside calif
Re: Victor VI crank
I think if you could some JB weld in that crack then clamp it together it could work. I may be a good idea as above to look for a new reproduction and save the old one as an original. Tom
-
- Victor Monarch Special
- Posts: 8516
- Joined: Tue Feb 10, 2009 11:25 am
- Personal Text: Stop for a visit when in Oregon.
- Location: Albany, Oregon
Re: Victor VI crank
Maybe instead of a reproduction buy an early XVI gold crank with the same distance from the wood knob to the turn. Take it to a machinist, have it cut to the correct length and have slot cut.
I think I'd repair the original as mentioned in prior posts, inspect it occasionally, and then cut down a similar Victrola crank if needed. I might even do both and keep the original inside the cabinet.
Jerry B.
I think I'd repair the original as mentioned in prior posts, inspect it occasionally, and then cut down a similar Victrola crank if needed. I might even do both and keep the original inside the cabinet.
Jerry B.