Page 1 of 3
Help! my edison standard is spinning way to fast
Posted: Sun Jan 19, 2020 8:01 pm
by dzavracky
Hey guys,
I am getting really frustrated trying to get my edison standard to spin at the right speed. It was almost spinning double before i started. Its closer now but I dont know what to do anymore. I have the speed adjustment set so it slows the speed as much as possible. I dont know what to do? Can i move the govenor over so it can't open up as much?
david
Re: Help! my edison standard is spinning way to fast
Posted: Sun Jan 19, 2020 8:28 pm
by Curt A
Your governor has "brake pads" mounted on a lever that is meant to slow down the speed that it spins at... It works similar to disc brakes on a car... the more pressure the pads exert on the governor disc, the slower it runs. Without actually seeing a picture of your motor or the governor, it is hard to tell what exactly needs adjusting... Sometimes the pads have worn out and don't touch the governor disc to slow it or the linkage from the speed control to the governor is bent or out of adjustment... It sounds like your problem lies in this area, but like I said without a picture, it is hard to guess...
Re: Help! my edison standard is spinning way to fast
Posted: Sun Jan 19, 2020 9:15 pm
by Curt A
Make sure that the governor is adjusted correctly as seen in the following two pictures. Also, the brake pad should be intact and able to touch the governor disc. Make sure that the brake lever linkage is not bent - it should look like the small picture... Hope this helps.
Re: Help! my edison standard is spinning way to fast
Posted: Mon Jan 20, 2020 3:23 pm
by dzavracky
OKAY great! this should fix the issue!
SO i should adjust the govenor so it touches the brake pad in the stop position?
(Edit) I tried moving the pin on the right and it didn’t work. What do I move to get the governor closer to the brake wheels?
Re: Help! my edison standard is spinning way to fast
Posted: Mon Jan 20, 2020 7:17 pm
by Curt A
The governor looks to be in the correct position...
Re: Help! my edison standard is spinning way to fast
Posted: Mon Jan 20, 2020 8:22 pm
by Governor Flyball
Curt A wrote:The governor looks to be in the correct position... It appears that the "brake lever" (speed control lever) may be moving too freely, since it appears to be centered in the slot in the bedplate. If it was holding, it should stay in a position closer to one end of the slot or the other... in other words, when you move the speed control lever it should stay in the position that you set it in, if this makes sense.
The brake lever is not the speed control lever. The brake lever swings fully out of the way when the phonograph is switched on.
The governor brass stirrup has two pads and it's position hence speed is controlled by a screw. If the machine runs too fast with the screw adjustment of the stirrup at its extreme minimum speed position, this suggests the disc and flyballs have been located incorrectly. Look and you will find the governor disc may be relocated by means of a set screw at hub holding the flyball spring straps at the other end of the rotating governor assembly. It should be positioned so that when the correct speed is attained, the speed adjustment screw will be roughly mid range.
Re: Help! my edison standard is spinning way to fast
Posted: Mon Jan 20, 2020 8:32 pm
by Curt A
What he said... I stand corrected...
Re: Help! my edison standard is spinning way to fast
Posted: Mon Jan 20, 2020 8:43 pm
by gramophoneshane
And don't forget, NEVER make adjustments to the governor without first letting the motor/main spring run completely down.
Re: Help! my edison standard is spinning way to fast
Posted: Mon Jan 20, 2020 9:13 pm
by dzavracky
Alrighty! I’ll have to give it a shot this weekend after my classes are over. And yes! I have been very careful to let it unwind all the way
Re: Help! my edison standard is spinning way to fast
Posted: Mon Jan 20, 2020 11:36 pm
by JimN
I'm guessing that oil on the brake pads would not be desirable, but I'm no expert.
Jim Nichol