FOUND: Victor 4-3 parts
-
- Victor IV
- Posts: 1228
- Joined: Fri Jun 08, 2012 1:14 pm
FOUND: Victor 4-3 parts
Need the back bracket and (2) screws for the tone arm on my Vic 4-3. Thanks
- Attachments
-
- 016.JPG (79.43 KiB) Viewed 1312 times
-
- 015.JPG (79.76 KiB) Viewed 1312 times
Last edited by dutchman on Wed Jun 24, 2015 4:29 pm, edited 1 time in total.
- briankeith
- Victor IV
- Posts: 1874
- Joined: Mon Jul 25, 2011 8:27 am
- Personal Text: Jeepster
- Location: Blairstown, New Jersey 07825
Re: WANTED for Victor 4-3
JAS,,,(?) Phonograph has them on EBay - I did mine and posted photos somewhere on here - a perfect repro - no issues. Getting the old one apart was a pot-metal nightmare 

- briankeith
- Victor IV
- Posts: 1874
- Joined: Mon Jul 25, 2011 8:27 am
- Personal Text: Jeepster
- Location: Blairstown, New Jersey 07825
Re: WANTED for Victor 4-3
JAS EBAY ITEM # 221428942590
- OrthoSean
- Victor V
- Posts: 2912
- Joined: Thu Jan 08, 2009 1:33 pm
- Location: Near NY's Capital
Re: WANTED for Victor 4-3
Ron Sitko also carries them for about $70 - 518-371-8549. They're excellent.
Sean
Sean
- DGPros
- Victor III
- Posts: 502
- Joined: Sun Apr 01, 2012 11:22 am
- Personal Text: Gary
- Location: Flemington NJ
Re: WANTED for Victor 4-3
I just replaced mine and picked it up from Ron Sitko at the Union show for my 8-12.Worked like a charm. Yes, it was a pain to remove the old one, just take your time and protect your sound arm.
In short, is not liberty the freedom of every person to make full use of his faculties, so long as he does not harm other persons while doing so?
Frederic Bastiat
Frederic Bastiat
- mattrx
- Victor IV
- Posts: 1162
- Joined: Wed Oct 12, 2011 9:55 am
- Location: Bartlett, TN
Re: WANTED for Victor 4-3
Just another note to say the the ones from both JAS and Ron are fantastic. I have bought both and used both without any issues whatsoever. If Ron has the size you need, he is a little cheaper. There is a size that Ron doesn't carry that JAS does, but I cannot remember which machine I had that issue with.
Good Luck!
Matt
Good Luck!
Matt
-
- Victor IV
- Posts: 1228
- Joined: Fri Jun 08, 2012 1:14 pm
Re: WANTED for Victor 4-3
Thanks for the info I'll give Ron a call. Cheers \
Bill K
Bill K
- coyote
- Victor II
- Posts: 455
- Joined: Thu Jan 08, 2009 12:41 am
- Location: Pittsburgh, PA
- Contact:
Re: WANTED for Victor 4-3
Both Justin Schaub and Ron Sitko are excellent to deal with.
-
- Victor IV
- Posts: 1228
- Joined: Fri Jun 08, 2012 1:14 pm
Re: WANTED for Victor 4-3
Thanks again gentlemen - I'll give Ron a call this evening. If I recall he is hard to contact before 7 PM. Believe I read somewhere there are several versions of the back bracket. Cheers
Bill K
Bill K
- alang
- VTLA
- Posts: 3116
- Joined: Thu Aug 19, 2010 9:36 am
- Personal Text: TMF Moderator
- Location: Delaware
Re: WANTED for Victor 4-3
You will need the number of screws that the bracket is fastened with and the distance between the screw holes.
Andreas
Andreas