Can you Identify this Horn that I bought?

Discussions on Talking Machines & Accessories
User avatar
hearsedriver
Victor III
Posts: 571
Joined: Wed Jan 25, 2017 10:21 pm
Location: Ft.Worth, Texas

Re: Can you Identify this Horn that I bought?

Post by hearsedriver »

Thanks!

User avatar
Chuck
Victor III
Posts: 891
Joined: Fri Mar 25, 2011 11:28 pm
Personal Text: Richards Laboratories http://www.richardslaboratories.com producing high quality cylinder blanks
Contact:

Re: Can you Identify this Horn that I bought?

Post by Chuck »

That horn looks brand new again!
"Sustained success depends on searching
for, and gaining, fundamental understanding"

-Bell System Credo

User avatar
phonogfp
Victor Monarch Special
Posts: 8021
Joined: Wed Jan 07, 2009 5:08 pm
Personal Text: "If you look for the bad in people expecting to find it, you surely will." - A. Lincoln
Location: New York's Finger Lakes

Re: Can you Identify this Horn that I bought?

Post by phonogfp »

Nice job! :)

Yes, the rattle-can paint can be annoying with all the "...recoat within 45 minutes or after 48 hours..." jazz. I was painting a bedplate for a coin-op about 8 years ago, and wasn't able to recoat within the timeframe, so I waited 4 or 5 days just to play it safe. The darn paint still crinkled. Strip and start over... :roll:

George P.

User avatar
fran604g
Victor VI
Posts: 3992
Joined: Mon Mar 04, 2013 2:22 pm
Personal Text: I'm Feeling Cranky
Location: Hemlock, NY

Re: Can you Identify this Horn that I bought?

Post by fran604g »

hearsedriver wrote:I had some issues with the semi-gloss enamel when I went to recoat it so, I ended up stripping it again and using an automotive matte black acrylic lacquer and am quite pleased with the results. I used a gold paint pen to do the stripping which was very easy to use. I might add a coat of orange shellac to the gold stripping to age it a little. I havent decided. Should have the decals here on saturday.
I agree with the others; very nice looking job! Would you share which "automotive matte black acrylic lacquer" you used, and is there a full spectrum of colors available? Spray bomb, or mix your own and apply with a gun?

-Fran
Francis; "i" for him, "e" for her
"Even a blind squirrel finds a nut once in a while" - the unappreciative supervisor.

User avatar
hearsedriver
Victor III
Posts: 571
Joined: Wed Jan 25, 2017 10:21 pm
Location: Ft.Worth, Texas

Re: Can you Identify this Horn that I bought?

Post by hearsedriver »

Hey guys. I just used spray cans from my local O'Rielly Auto Parts store and a paint pen from Walmart craft department. It took 3 cans of the black lacquer. The paint pen works remarkably well. I didnt have to tape off anything. These come in several tips. I used the largest chisel tip. 1 pen allowed me to do 2 coats and, its good paint. For the black, I sanded the horn with 800 grit paper, primed it, wet sanded with 800 grit paper, sprayed 2 coats of black lacquer, let dry for 2 hours, wet sanded it with 1000 grit paper, sprayed 2 more coats of black. Its not perfect but, I didnt want it to be since its 100 years old. Like I said, I may add a coat of either Bulls Eye amber shellac or amber tinted lacquer with a brush to the gold stripping to tone it down a Little but, the more I look at it, the more I like the current color of the gold, plus, it will probably match the decals better, as-is.
Attachments
001.JPG
001.JPG (124.79 KiB) Viewed 1183 times
002.JPG
002.JPG (43.34 KiB) Viewed 1183 times

User avatar
hearsedriver
Victor III
Posts: 571
Joined: Wed Jan 25, 2017 10:21 pm
Location: Ft.Worth, Texas

Re: Can you Identify this Horn that I bought?

Post by hearsedriver »

Here she is all mounted up.
Attachments
004.JPG
004.JPG (100.76 KiB) Viewed 1154 times

Post Reply