I bought a turntable for my Vic I type D and it's supposed to be the correct turntable for late outside horn machines, but it doesn't seem to fit properly. The pin on the motor's spindle is too low on the spindle for the turntable to settle on it and it just keeps reacing down until it rests on the brake. The thickness on the upper part of the spindle is about 8 millimeters and the lower part about 9 millimeters (metric system, sorry). Could it be that the spindle got some kind of modification or might I be adjusting it wrong?
Thanks for any help and advice in advance
Need help with turntable for Vic I type D not fitting
-
- Victor O
- Posts: 59
- Joined: Sun Apr 15, 2018 12:36 pm
- Location: Iceland
- AZ*
- Victor IV
- Posts: 1143
- Joined: Thu Jan 15, 2009 8:51 pm
- Location: USA
Re: Need help with turntable for Vic I type D not fitting
Based on what you've said and the photos, the turntable appears to be riding low. In my experience, there are 2 things which typically cause this.
1. The washers between the motor frame and the bottom of the motor board are too thick. or
2. The ball bearing that the turntable spindle rests on inside the hole in the motor frame is missing. Sometimes these are misplaced during motor overhauls.
If it's not one of those two, then I don't know.
Good luck.
1. The washers between the motor frame and the bottom of the motor board are too thick. or
2. The ball bearing that the turntable spindle rests on inside the hole in the motor frame is missing. Sometimes these are misplaced during motor overhauls.
If it's not one of those two, then I don't know.
Good luck.
Best regards ... AZ*
-
- Victor O
- Posts: 59
- Joined: Sun Apr 15, 2018 12:36 pm
- Location: Iceland
Re: Need help with turntable for Vic I type D not fitting
Do you know where I could find a ball bearing?AZ* wrote:Based on what you've said and the photos, the turntable appears to be riding low. In my experience, there are 2 things which typically cause this.
1. The washers between the motor frame and the bottom of the motor board are too thick. or
2. The ball bearing that the turntable spindle rests on inside the hole in the motor frame is missing. Sometimes these are misplaced during motor overhauls.
If it's not one of those two, then I don't know.
Good luck.
- Zwebie
- Victor IV
- Posts: 1466
- Joined: Thu Feb 23, 2012 2:55 pm
- Personal Text: We are only the caretakers for future generations.
- Location: FLORIDA
Re: Need help with turntable for Vic I type D not fitting
Thorhallur,
You need the Victor 10" turntable with the longer pedestal under the base, (see pictures).
Your turntable will work on an earlier Vic.I or Vic.II.
Bob S.
You need the Victor 10" turntable with the longer pedestal under the base, (see pictures).
Your turntable will work on an earlier Vic.I or Vic.II.
Bob S.
-
- Victor II
- Posts: 364
- Joined: Tue Aug 14, 2018 7:35 pm
- Location: Syracuse N.Y.
Re: Need help with turntable for Vic I type D not fitting
Just a couple of observations based on your pictures. The turntable looks uneven- higher on the left than on the right- The correct turntable ought to be perfectly flat- the paper shim washers are responsible for this. At the same time, the crank should screw into the winding shaft without binding, in the least ! Trial and error unless you are extremely well versed in very accurate measurements. Patience will out.
- Zwebie
- Victor IV
- Posts: 1466
- Joined: Thu Feb 23, 2012 2:55 pm
- Personal Text: We are only the caretakers for future generations.
- Location: FLORIDA
Re: Need help with turntable for Vic I type D not fitting
That's because it's resting on the brake lever on the left side.The turntable looks uneven- higher on the left than on the right
-
- Victor Monarch Special
- Posts: 8732
- Joined: Tue Feb 10, 2009 11:25 am
- Personal Text: Stop for a visit when in Oregon.
- Location: Albany, Oregon
Re: Need help with turntable for Vic I type D not fitting
If Zwebie is correct you could check with a common 12" turntable from a typical later Victrola X or XI. It would give you an idea about the correct fit on the spindle. Jerry
- AZ*
- Victor IV
- Posts: 1143
- Joined: Thu Jan 15, 2009 8:51 pm
- Location: USA
Re: Need help with turntable for Vic I type D not fitting
Zwebie is probably right. It looks like Thor has the incorrect turntable for his Victor I.
Best regards ... AZ*
-
- Victor O
- Posts: 59
- Joined: Sun Apr 15, 2018 12:36 pm
- Location: Iceland
Re: Need help with turntable for Vic I type D not fitting
Thanks!Zwebie wrote:Thorhallur,
You need the Victor 10" turntable with the longer pedestal under the base, (see pictures).
Your turntable will work on an earlier Vic.I or Vic.II.
Bob S.
-
- Victor Monarch Special
- Posts: 8732
- Joined: Tue Feb 10, 2009 11:25 am
- Personal Text: Stop for a visit when in Oregon.
- Location: Albany, Oregon
Re: Need help with turntable for Vic I type D not fitting
Thorhallur, I think I've finally found the turntable you need. I'd welcome other opinions.
Jerry Blais
Jerry Blais