Need some opinions on which machine to sell :/

whoopinola · Post by **whoopinola** » Fri Jan 18, 2013 8:40 pm

The other posts are spot on...Oak VV-IXs are pretty thin on the ground. This machine would be much easier to sell ,and harder to replace...The VV-260 wasn't a popular machine in the 20's , and I think it would be a hard sell today...you certainly won't get top dollar for it...I've got an oak VV-IX and a VV-240...I'd just about give the 240 away just to make room...the VV-IX?..not for sale!...no matter what price is offered!

Tyler94 · Post by **Tyler94** » Fri Jan 18, 2013 11:36 pm

Jerry B. wrote:Tyler, If you are married, you could ask your wife. Mine is never wrong.

Well I'm only 18 so not married just quite yet

Tyler94 · Post by **Tyler94** » Fri Jan 18, 2013 11:43 pm

whoopinola wrote:The other posts are spot on...Oak VV-IXs are pretty thin on the ground. This machine would be much easier to sell ,and harder to replace...The VV-260 wasn't a popular machine in the 20's , and I think it would be a hard sell today...you certainly won't get top dollar for it...I've got an oak VV-IX and a VV-240...I'd just about give the 240 away just to make room...the VV-IX?..not for sale!...no matter what price is offered!

ahh i see i see, the vv-260 was my first machine i purchased and the ix i saw at a antique shop for $130 so i could not pass it up! had no clue of the small amounts of them made in oak however!

Duchesne · Post by **Duchesne** » Sat Jan 19, 2013 7:44 am

If you were looking to sell these on ebay, the smaller one is easier to sell as it's portable and you can sell overseas as well. The bigger model is heavier and cumbersome. Oak tends to be more liked than Mahogany.
Personally, I would sell the one that doesn't play quite as well or which one I don't like as much. It makes the choice less painful.

Good luck!
J

whoopinola · Post by **whoopinola** » Sat Jan 19, 2013 2:47 pm

You always remember fondly your first machine. Many years ago a marriage break up caused me to sell my first machine , an oak Columbia table top , and I still regret doing it...If you're living in Flat Rock Mich then we're not far apart since I live in Canada about 25 miles from Detroit..My point is that if you sell your VV-260 and in time your money worries disappear , you can replace it with my VV-240 for a token amount.. I believe that we should help the youth in this hobby...Steve

Tyler94 · Post by **Tyler94** » Sat Jan 19, 2013 10:51 pm

whoopinola wrote:You always remember fondly your first machine. Many years ago a marriage break up caused me to sell my first machine , an oak Columbia table top , and I still regret doing it...If you're living in Flat Rock Mich then we're not far apart since I live in Canada about 25 miles from Detroit..My point is that if you sell your VV-260 and in time your money worries disappear , you can replace it with my VV-240 for a token amount.. I believe that we should help the youth in this hobby...Steve

I couldn't agree with you more Steve, your first machine is like a milestone, and wow yeah your not far at all! i will seriously consider that, I leave for basic training July 15th so after i will have a little spending cash to put to good use! . Thank you very much for the reply Steve - Tyler...btw keep warm with this blistering cold front we have on the way!

whoopinola · Post by **whoopinola** » Sun Jan 20, 2013 2:04 pm

Going into the military?? Well good luck lad , I wish you well..The deal still goes, except that the "token" just got smaller... and as an added bonus , there's a basket case "Mitchel" consol machine made in Detroit with your name on it...just come and get it...Steve

Tyler94 · Post by **Tyler94** » Sun Jan 20, 2013 6:38 pm

whoopinola wrote:Going into the military?? Well good luck lad , I wish you well..The deal still goes, except that the "token" just got smaller... and as an added bonus , there's a basket case "Mitchel" consol machine made in Detroit with your name on it...just come and get it...Steve

Yes I'm going into the Marines & Wow ! Steve that would be great, Thank you very much sir. Ive never heard of a "Mitchel" before? learn something new everyday.

whoopinola · Post by **whoopinola** » Sun Jan 20, 2013 9:42 pm

Good luck again...Do what you've got to do now...when you get back I'll see to it that you've got a machine or two to get restarted in the hobby...The "Mitchel" is yours if you want it...It needs a lot of work , and only a Detroiter will give a damn about it...Last I heard the old Mitchel factory was still standing...

edisonrestorer64 · Post by **edisonrestorer64** » Mon Jan 21, 2013 7:03 pm

Yes the 1X is the best one sleake yest poortable

Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/

Re: Need some opinions on which machine to sell :/